Choosing a Decorative Rock Cover? Start with a Tape Measure

Editorial illustration of measuring the complete outside diameter of a garden inspection lid before choosing a hollow rock cover.

The awkward bit of the garden is often quite small: a lid in the lawn, a valve beside the path, a pipe that catches your eye from the kitchen. A decorative rock cover can help it blend in. The expensive mistake is choosing the nicest-looking stone before checking the space underneath.

Illustrated measuring scene. The cover shown is not a technical drawing of a particular GARTENDEK model.

In this guide
  1. Measure the whole object, not just the lid
  2. Build a shortlist from the published dimensions
  3. What the results mean — and what still needs checking
  4. A wide low cover and a tall cover solve different problems
  5. Make room to lift it off again
  6. Let the garden do some of the styling
  7. Questions before ordering

Measure the whole object, not just the lid

Take the outside dimensions, including the rim, hinges, handles, fittings and anything that sticks out. Measure height from the ground where the cover will actually stand. A sloping patch of lawn can change that reference point. For a box or a cluster of components, measure the full enclosing rectangle.

Before choosing any cover, check that the equipment may be covered at all. Manufacturer instructions and utility-provider requirements take priority. Keep required ventilation, safety devices and service access clear; do not cover gas or electrical equipment unless the responsible provider or manufacturer explicitly permits it.

Three measurements before choosing a cover
Include every protrusion

Measure the outside rim, handles and fittings — not the opening inside the lid.

Use the correct footprint

Round: full diameter. Rectangular: length and width; the finder checks their diagonal with your allowance.

Measure from the resting ground

Include the full height. Check clearance at that height, not only at the top of the stone.

Outside stone dimensions describe its appearance. The cavity shape determines what can go underneath.

Build a shortlist from the published dimensions

The finder below uses covering diameters stated on the current product pages. Where a page gives an explicit useful inner height, it uses that figure; for a published range, it uses the lower end. It never treats the outside height as the available space inside.

GARTENDEK · SIZE FINDER

Find rock covers to check

Enter the full outside size of your object. Results are a dimensional shortlist, not a fit guarantee.

Measure the whole object. Compare a round diameter or the diagonal of an expanded rectangular footprint with the published covering diameter. Confirm internal height and cavity shape before ordering.

Size check only. Covering must be permitted for the equipment; keep required ventilation and service access.

How the screen works

Round: diameter + 2 × clearance. Box: diagonal after expanding length and width by 2 × clearance. Height: object height + clearance.

Dimensions checked against product descriptions on 30 October 2026. Stock and final fit are not checked live.

What the results mean — and what still needs checking

A round lid is screened by its diameter. A rectangular object is screened by its diagonal: a 30 × 40 cm rectangle needs a 50 cm circle before any extra clearance. This is a deliberately conservative method. An elongated hollow stone might accommodate a shape that this circular screen leaves out.

Clearance in the tool is simply extra planning space that you choose. It is not a replacement for the manufacturer’s ventilation or maintenance requirements. The finder also checks height. If the page publishes no usable inner height, the model goes into a separate group that needs a height check.

Even a model within the published screening limits is only a candidate. These are irregular shells: the cavity narrows, the highest point sits somewhere near the middle, and the width available at lid height may be smaller than the width at ground level. Send your dimensions and a photo for confirmation before ordering when the fit is close.

A wide low cover and a tall cover solve different problems

A shallow inspection lid usually calls for width without much visual bulk. An upright fitting needs more height, but that does not mean every broad stone has enough room above it. Think in three dimensions rather than shopping by S, M or XL alone.

The catalogue illustrates the difference. S-07 lists about 45 cm of covering diameter and about 20 cm of inner clearance. M-04 lists about 51 cm of covering diameter and approximately 38–39 cm of useful inner height. Neither is a universal answer: the shape of your object still matters.

Make room to lift it off again

Imagine the next inspection before arranging the planting. Can the cover be lifted clear? Is there somewhere nearby to put it? Will plants, edging or gravel block the service opening? The attractive arrangement is the one you can put back after maintenance without rebuilding the bed around it.

Keep loose material away from the opening. Do not screw, bury or permanently secure a cover unless both the product instructions and the installation requirements allow it. Check the product’s handling guidance, particularly for larger models.

Decorative rock cover beside a path, shown over an inspection lid and lifted to reveal it.
A removable decorative rock cover shown closed and lifted for inspection access.

Let the garden do some of the styling

Choose a colour that sits comfortably with nearby paving, gravel and planting. Positioning the stone beside a bed edge or a loose group of plants often feels more settled than placing it alone in the middle of a perfect lawn. Keep the technical opening accessible rather than hiding it beneath dense planting.

Take one photo from the view you use most — a window, the terrace or the gate. That tells you more about visual scale than a close-up of the lid. A cover should quieten the scene, not become the garden’s biggest talking point by accident.

Questions before ordering

Does the finder guarantee that a model fits?

No. It screens published dimensions and separates models with missing inner-height data. Irregular cavity shape and clearance at the object’s full height still need confirmation.

Why does a rectangular box need such a large diameter?

The circular screening method must contain its corners. The tool adds clearance to both sides of the length and width before calculating the diagonal. It can miss an elongated cavity that would work after a detailed shape check.

What should I send for a final fit check?

Send a photo, the complete outside dimensions, the height above the intended resting ground and the equipment’s access or ventilation requirements. Include a sketch of any protrusions.

A few careful measurements are less exciting than choosing a colour. They are also what lets you enjoy the finished garden without wondering whether you ordered the wrong stone.

All published covering diameters (19)

A comparison of published descriptions. Only explicitly stated useful inner height is shown; ranges use the lower end.

GARTENDEK S-04Ø 33 cm · approx.Published inner height, approx.: —
GARTENDEK S-01Ø 39 cm · approx.Published inner height, approx.: —
GARTENDEK S-02Ø 41 cm · approx.Published inner height, approx.: —
GARTENDEK S-06Ø 42 cm · approx.Published inner height, approx.: —
GARTENDEK S-07Ø 45 cm · approx.Published inner height, approx.: 20 cm
GARTENDEK S-03Ø 45 cm · approx.Published inner height, approx.: —
GARTENDEK S-05Ø 49 cm · approx.Published inner height, approx.: —
GARTENDEK M-04Ø 51 cm · approx.Published inner height, approx.: 38 cm
GARTENDEK L-03Ø 60 cm · approx.Published inner height, approx.: —
GARTENDEK L-04Ø 67 cm · approx.Published inner height, approx.: —
GARTENDEK M-02Ø 73 cm · approx.Published inner height, approx.: —
GARTENDEK M-01Ø 73 cm · approx.Published inner height, approx.: —
GARTENDEK L-02Ø 75 cm · approx.Published inner height, approx.: —
GARTENDEK XL-01Ø 80 cm · approx.Published inner height, approx.: 18 cm
GARTENDEK M-03Ø 80 cm · approx.Published inner height, approx.: —
GARTENDEK L-01Ø 80 cm · approx.Published inner height, approx.: —
GARTENDEK XL-04Ø 90 cm · approx.Published inner height, approx.: 20 cm
GARTENDEK XL-02Ø 90 cm · approx.Published inner height, approx.: 21 cm
GARTENDEK XXXL-01Ø 140 cm · approx.Published inner height, approx.: 50 cm